Vanity

Re: Vanity

Unread post #21 by JojoD818 » Mon Nov 27, 2017 11:12 pm

Grabe ang ganda!
User avatar
JojoD818
Sr. Member
Sr. Member
 
Posts: 565
Joined: Sat Nov 30, 2013 7:50 pm

Share On:

Share on Facebook Facebook Share on Twitter Twitter

Re: Vanity

Unread post #22 by bigfoot » Thu Nov 30, 2017 8:09 pm

Ding,

I think 3Hp motors should be minimum for you. :D
Your cutting tools is only as good as your sharpening system.
User avatar
bigfoot
Admin
Admin
 
Posts: 1886
Joined: Fri Feb 24, 2012 1:01 am

Re: Vanity

Unread post #23 by timber715 » Thu Nov 30, 2017 10:11 pm

bigfoot wrote:Ding,

I think 3Hp motors should be minimum for you. :D

5Hp would be better... :lolno: :lolno:
Image
User avatar
timber715
Admin
Admin
 
Posts: 4700
Joined: Fri Feb 24, 2012 12:47 am

Re: Vanity

Unread post #24 by balarila » Sat Dec 02, 2017 8:07 am

Finished cutting and milling all the legs, rails, and stiles. Punched through the mortises into the legs. Marked up the tenons.
Image
Image

Some months back, I splurged on a Jet mortising machine from Panda. Wish I had done this a long time ago as chiseling mortises just takes too much time.
I'd rather add life to my years than years to my life.
User avatar
balarila
Sr. Member
Sr. Member
 
Posts: 2316
Joined: Sun Mar 04, 2012 10:11 am
Location: Antipolo, Rizal

Re: Vanity

Unread post #25 by joey81 » Sat Dec 02, 2017 10:27 am

There's a 12" jointer downhill that you can use while yours is waiting to be fixed. :wave:
Rotir Tools * Bosch * Dremel * Hitachi * Dewalt * Freud * Harbor Freight * Woodpecker * Incra * Skil * Whiteside * CMT * Grizzly
User avatar
joey81
Sr. Member
Sr. Member
 
Posts: 2046
Joined: Mon Mar 05, 2012 12:05 pm

Re: Vanity

Unread post #26 by balarila » Sat Dec 02, 2017 10:48 am

joey81 wrote:There's a 12" jointer downhill that you can use while yours is waiting to be fixed. :wave:


Ha-ha. Thanks! I may just take you up on it on the next project. Buti na lang, my flattening was about 90% complete when my jointer burned out. Binraso ko na lang ng jointer plane.
I'd rather add life to my years than years to my life.
User avatar
balarila
Sr. Member
Sr. Member
 
Posts: 2316
Joined: Sun Mar 04, 2012 10:11 am
Location: Antipolo, Rizal

Re: Vanity

Unread post #27 by balarila » Mon Dec 04, 2017 8:06 am

Didn't have so much time over the weekend. Just managed to cut the tenons and route some rabbets where the plywood sides and floors will go.

Image


I had this tenoning jig for a some time now. Used it once before. It's really a breeze cuting tenons. And very accurate, too.

Test fitting.

Image
Image
I'd rather add life to my years than years to my life.
User avatar
balarila
Sr. Member
Sr. Member
 
Posts: 2316
Joined: Sun Mar 04, 2012 10:11 am
Location: Antipolo, Rizal

Re: Vanity

Unread post #28 by Violaine » Wed Dec 06, 2017 5:02 am

nice project..smooth and slow...
very nice wood too...if scarce, veneering is my way to go! haha
I think i was a woodworker in my previous life...and the life previous to that.
User avatar
Violaine
Sr. Member
Sr. Member
 
Posts: 2998
Joined: Sat Mar 03, 2012 10:06 pm

Re: Vanity

Unread post #29 by balarila » Tue Dec 12, 2017 1:31 pm

All glued up. Now working on the drawers.

Image
I'd rather add life to my years than years to my life.
User avatar
balarila
Sr. Member
Sr. Member
 
Posts: 2316
Joined: Sun Mar 04, 2012 10:11 am
Location: Antipolo, Rizal

Re: Vanity

Unread post #30 by timber715 » Tue Dec 12, 2017 5:22 pm

sayang naman yan kung ganyang palywood gagamitin mo. Birch plywood dapat minimum... :lolno: :lolno: :lolno:
Nice work Ding...
Image
User avatar
timber715
Admin
Admin
 
Posts: 4700
Joined: Fri Feb 24, 2012 12:47 am

PreviousNext

Return to Woodworking



Who is online

Users browsing this forum: No registered users and 1 guest

cab1net advertisements
  • Advertisement
  • Place your adds here